Why Understanding Plumbing Basics is Essential When Installing a Bathtub
Why Understanding Plumbing Basics is Essential When Installing a Bathtub
Blog Article
Everybody may have their own individual piece of advice involving Installing A Bathtub.
Setting up a bath tub isn't precisely rocket science, yet it does need strong plumbing, carpentry, as well as in some cases, tiling skills. Changing an old tub with a new one is also a moderately tough project. If the old bathtub is readily obtainable, the project can move immediately; if you need to open a wall surface to eliminate the old tub as well as position the new bath tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will need an assistant to leave the old bathtub and set in the brand-new one. Ensure you have actually qualified on your own for the job and also fit trying it. Rather than hiring a service provider to take over a halfway-completed project, it is much better to take into consideration employing one before you start. Opportunities are you might need a professional plumber to make tube links.
This write-up will certainly aid you mount a new bathtub in your washroom if you have actually currently gotten a new bathtub as well as don't require to change the setup of your previous water pipes.
Your tools and product list need to comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you must do is separate the supply of water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be quite problematic because of the restricted access that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will originate from the pipelines. As soon as the supply pipes have been removed, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to going on to fit the new faucets, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin ensuring that the washing machines remain in area between the tap and the sink. Protect the tap in place with the producer offered backnut. Once the tap is firmly in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap ports. The former type needs to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using both wooden boards under its feet, put the bathtub in the needed placement. The wood boards are valuable in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level and changing the feet on the tub until the level reviews degree.
To set up taps, fit all-time low of the outermost versatile tap adapter to the ideal supply pipe by making a compression join; after that do the exact same for the various other faucet.
Switch on the water supply and also check all joints and also new pipework for leakages and tighten them if essential. Fill up the bath tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, fix the bath paneling as explained in the maker's instruction manual. Tiling and also sealing around the bath tub should wait up until the bathtub has been used a minimum of once as this will resolve it into its final setting.
Planning for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be suited its final setting.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness as well as possible leaks to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes as well as cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealer can break relatively very early if you do not think about this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently offered on the marketplace. It is recommended to fit the tiles using water-resistant or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on How to Install a Bathtub? Give a review directly below. We will be glad to hear your insights about this page. We hope that you come back again before long. Sharing is good. You just don't know, you may very well be helping someone out. Thanks a lot for your time spent reading it.
Click Here Report this page